Web Menu

Product Search

Language

Share

News

Home / News

  • Jan 15,2022

    How can forklift tires reduce wear?

    Frequent replacement of forklift tires is not a good thing. It is not only time-consuming but also causes a lot of waste. So Zhejiang Kunrong Rubber Technology Co., Ltd. hereby reminds you to use forklifts reasonably, which not only saves time and effort, but also ensures long-term safety/safety work. A guarantee, let's take a look: How to reduce the wear of forklift tires? 1. Strengthen the maintenance of tires.Do a good job of land survey and pressure cleaning, check the temperature of the tires, and the grounding holes are blocked.Usually when inflating tires, if it is cold and under a certain load, regularly check and adjust the tire pressure at least once a month; in summer, due to the high ambient temperature, if the tire temperature is too high, reduce the frequency of increase to avoid strong sunlight to the tires , it is recommended to stop in the shade of a tree, instead of directly pouring cold water for cooling or directly venting to reduce pressure. If you are going to leave it in the open parking lot for a long time in winter, you should base it on the tires and don't start accelerating immediately until the tires get hot, and then it becomes normal driving. 2. Improve driving skills.Lift the clutch pedal slowly and steadily when starting off. The maximum speed of driving must not exceed the speed limit of the tire; it should be avoided as much as possible during the process of rapid acceleration, emergency braking and sharp turning. In the case of obstacles such as rocks and potholes, it is recommended that you slow down as much as possible or avoid it directly.3. Improve the maintenance of the chassis.Lubricate and adjust the design value of wheel hub bearing, tie rod ball end, king pin bushing in time according to regulations; keep the balance of the tire, if it is unbalanced, the wheel dynamic balance test should be used to exhaust the one-way valve frequently, and the tire has been oiled. Once the forklift is found Tire into oil, you should immediately remove the tire to clean, and check the air seal at the same time, replace the tire winter tire in the greenhouse to restore / restore elasticity / elasticity, load the rim forklift tire product Apply soap in the fetal port to prevent damage to the port; pivot oil Sealing and brake hydraulic cylinders should be leak-free, and oil- and wet-resistant rubber tires should meet the requirements for lateral and radial swinging wheel assemblies.

    View more +

  • Dec 03,2021

    Why use solid tires for forklifts?

    1. Excellent safe use performance is conducive to improving work efficiencyBecause the solid tire carcass is made of all rubber, the puncture resistance of the tire is ensured to the greatest extent, and the hidden danger of tire puncture during the load-bearing operation of industrial vehicles and in the harsh working environment is fundamentally eliminated. The load-deformation of solid tires is small, and the running stability is good. Because of its puncture resistance and tear resistance, it does not need to be inflated. It avoids the heavy labor of frequent tire replacement and can improve the utilization rate and work efficiency of the vehicle. It can run at low speed and efficiently. In vehicles, solid tires can completely replace pneumatic tires.2. Reasonable structural design to ensure that the tire has better performanceThe solid tire adopts an advanced three-stage structure design, and the three rubber materials respectively ensure the overall performance of the tire. High-rigidity, high-strength base rubber and steel ring support not only ensure the stiffness of the tire, but also ensure the tightness between the tire and the rim, and fundamentally eliminate the slip ring problem of solid tires; the high-elastic intermediate rubber effectively It absorbs the vibration generated when the vehicle is running, and has a comfortable driving performance, while avoiding damage to the vehicle; the thicker tread rubber layer ensures the tire's resistance to tearing and abrasion, and improves the service life of the solid tire;3. Advanced technology and formula designThe production of solid tires has advanced technology with more than half a century of production history and experience. The rubber formula design has maximized the performance of the tires, especially the base rubber is all imported high-rigidity, low-heat-generating rubber materials. The heat generation and temperature rise during operation are minimized, while the heat resistance of the tire is improved, thereby solving the serious problems of solid tires such as swelling, slippage, and burst caused by temperature rise; advanced formula design reduces the tire The rolling resistance. Tested by the National Construction Machinery Quality Supervision and Inspection Center, the coefficient of rolling resistance of solid tires is equivalent to that of pneumatic tires, which solves the problem of increased fuel consumption caused by changing to solid tires;4. Avoid vehicle tire blowouts and out-of-control dangers, and promote safe productionPneumatic tire rim-type solid tire is a solid tire that can be used interchangeably with pneumatic tires of the same specification. When the vehicle is driving at high speed, such as the tire hitting potholes and other obstacles, the tire will be severely squeezed and deformed between the obstacle and the rim flange, which can cause the carcass cord to break, and the compressed air inside the tire will break. The line is pushed up to form a bulge. In more serious cases, it will cause the tyre to rupture, and it will be completely flattened instantly and the vehicle may lose control. Compared with pneumatic tires, it has the advantages of high safety, puncture resistance, tear resistance, wear resistance and long life. It is an ideal replacement product for pneumatic tires in the field of industrial vehicles. With the development of industrial vehicles and the improvement of solid tire production technology, this type of tire has been used more and more widely.

    View more +

  • Dec 03,2021

    Why do more and more forklifts use solid tires?

    Because forklift solid tires have many advantages, solid tires have higher load performance, which can reduce the load area of tires and contact surfaces, greatly reduce tire wear machines, increase vehicle flexibility, and improve work efficiency. The inner part of the tire is filled with elastic adhesive paper. No matter it is used in any place, there is no tyre breakage or puncture. The design of multiple fastened travellers at the tire spigot can have sufficient strength to bear the weight and will not slip. It has good shock absorption performance, and the grip ability at room temperature and low temperature is combined with the pattern, and it is also suitable for roads in harsh environments.

    View more +

  • Dec 03,2021

    Correct handling method of forklift solid tire damage

    Solid tires are mainly used for industrial vehicles such as low-speed and high-load hoisting vehicles, towing vehicles and flatbed trucks. Solid tires are also widely used in various industries. Once they are damaged, how should they be dealt with?1. When the tire has cracks, holes, blisters, delamination, etc., it should be repaired or refurbished according to the specific conditions. If there are continuous cracks around the tire carcass, the tread rubber has been polished and there are large holes, the carcass line layer has annular cracks and the entire circle is separated, it should be replaced.2. When small holes are found in the inner tube, hot patch or cold patch can be performed. That is to say the roughness of the file around the damaged part of the inner tube, apply the fire repair rubber to the damaged place, and make the hole and the small hole just in the middle of the repair rubber, then install the tire repair clamp against the normal fire repair rubber, tighten the screw and press it again. Ignite the heating agent on the glue and wait for 10-15 minutes to bond tightly.3. Timely replacement: If the inner tube is folded, severely broken, aging, sticky, deformed and other problems that cannot be repaired, it needs to be replaced in time. At the same time, develop a regular check of the tire pressure, check once every other month, if the tire pressure is not enough, it should be refilled in time. Routine inspections are also required before going on the highway to ensure driving safety.

    View more +

  • Dec 03,2021

    How to choose solid tires and pneumatic tires for forklifts?

    A solid tire is a type of tire corresponding to a pneumatic tire (hollow tire). The carcass is solid and does not require cords as a skeleton and does not need to be inflated, so it does not need an inner tube or an inner liner. The earliest tires were solid tires. Solid tires are currently only used for high-load vehicles or machinery running at low speeds, as well as for fixed-position machinery.As a kind of construction machinery vehicle, forklifts often need to be loaded under some complex conditions. Therefore, forklift tires are mainly divided into two categories: forklift pneumatic tires and forklift solid tires. As the name suggests, the pneumatic tires of forklifts need to be inflated. Now that there are so many vehicles on the road, everyone is no stranger to it. It has the characteristics of easy installation, and the bumps are relatively small during driving. Compared with forklift pneumatic tires, forklift solid tires do not need to be inflated, and their carcass is solid. Forklift solid tires have better abrasion resistance and are not prone to tire breakage, so their lifespan is relatively long. , Generally 3-4 times that of pneumatic tires. In addition, it also has the advantages of oil resistance and chemical resistance, which is impossible for ordinary tires. But generally speaking, the standard equipment for forklifts is pneumatic tires. This is because pneumatic tires are the most widely used, and the price is much cheaper than solid tires.Pneumatic tires are easy to be compressed on complex roadsThe characteristics and advantages of pneumatic forklift tires: installation is relatively simple, easy to maintain, the forklift driver is less affected by bumps when using, the man-machine efficiency is better, and the price is relatively affordable; disadvantages: the service life is not as good as solid tires, such as In places where the road is relatively chaotic, when there are a lot of broken stones, iron filings, and waste residues on the ground, the hollow pneumatic tires are quite weak, have poor durability, and are also prone to puncture. Companies that use pneumatic tires in metal companies, such as hardware factories and spring factories, can easily happen if they don't pay attention.Then, the solid tire can solve this problem very well. Better durability, explosion protection, safety, strong weighing ability, etc. are all its advantages. The characteristics and advantages of solid forklift tires: good wear resistance, 3-4 times the service life of ordinary pneumatic tires, and no tire breakage (unless tire quality problems). Disadvantages: tires are harder and prone to bumps during installation. Troublesome, many procedures, if the installation is not good, it will cause slippage between the tire and the rim.Many customers hope that they can be equipped with solid tires when purchasing forklifts, so that they can be better adapted to various working conditions. However, we must know that the price of solid tires is much more expensive than that of pneumatic tires, which is about three times the price of ordinary pneumatic tires, which invisibly increases the cost of using forklifts. Take an ordinary diesel forklift of 3 tons and 3 meters, if the original 3 pneumatic tires are replaced with ordinary solid tires, it will cost about 3,000 yuan more.The solid tire is very hard and cannot cushion the forklift as a wholeFrom this point of view, there is only one weakness in price. If you can accept it, is it the best choice for a solid tire? Actually otherwise, as we mentioned earlier, pneumatic tires still have many potential advantages, such as less damage to the ground, quieter, convenient replacement and maintenance, lighter, more energy-saving, better shock absorption, and non-slip. Better performance, higher control sensitivity and so on. And because the solid tire is made of completely solid rubber. Although these tires can last a long time, they will not pop up or become deflated like pneumatic tires. But solid forklift tires are not conducive to prolonging the service life of forklifts because they do not provide air cushioning and ground cushioning between vehicles. In this way, the forklift is in a bumpy state for a long time, and it will be more prone to loss of life.Therefore, it seems that there is no absolute pros and cons, but you need to make purchases based on actual usage. If the ground is too bad, ordinary pneumatic tires cannot achieve abrasion resistance, puncture resistance, corrosion resistance, etc., then solid tires are a good choice. In addition, pneumatic tires are the best choice.

    View more +

Recent information

News

Contact Us

  • address:

    Zhejiang Kunrong Rubber Technology Co., Ltd., Hongsan Industrial Functional Zone, Sanhe Town, Tiantai County, Taizhou City, Zhejiang Province, China

  • Phone:

    86-+86-17767158016/+86-15558571818

  • Fax:

    0086-576-0576-83081222

  • Email:

    [email protected]